logo

한국어

SL-R6804

관리자 2016.04.06 12:46 조회 수 : 249

U-Boot 1.1.3 (May 19 2010 - 18:19:53)

Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fb4000
config usb..
spi_wait_nsec: 72
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000
.*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.4.0.0
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 256 Mbits SDR
DRAM bus: 16 bit
Total memory: 32 MBytes
Flash component: SPI Flash
Date:May 19 2010  Time:18:19:53
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

 ##### The CPU freq = 320 MHZ ####

SDRAM bus set to 16 bit
 SDRAM size =32 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

3: System Boot system code via Flash.
## Booting image at bf050000 ...
raspi_read: from:50000 len:40
.   Image Name:   MIPS OpenWrt Linux-3.10.32
   Created:      2014-04-15  19:45:58 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1001740 Bytes = 978.3 kB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:f490c
................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[    0.000000] Linux version 3.10.32 (router@router-virtual-machine) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40010) ) #1 Wed Apr 16 03:44:21 CST 2014
[    0.000000] SoC Type: Ralink RT3350 id:1 rev:2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[    0.000000] MIPS: machine is Asus RT-G32 B1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=0007b080
[    0.000000] Readback ErrCtl register=0007b080
[    0.000000] Memory: 29292k/32768k available (2184k kernel code, 3476k reserved, 551k data, 208k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 320MHz
[    0.000000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] pinctrl core: initialized pinctrl subsystem
[    0.100000] NET: Registered protocol family 16
[    0.150000] bio: create slab <bio-0> at 0
[    0.160000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.170000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.180000] Switching to clocksource MIPS
[    0.190000] NET: Registered protocol family 2
[    0.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.220000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.230000] TCP: Hash tables configured (established 512 bind 512)
[    0.240000] TCP: reno registered
[    0.250000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.270000] NET: Registered protocol family 1
[    0.280000] rt-timer 10000100.timer: maximum frequncy is 6510Hz
[    0.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.350000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.370000] msgmni has been set to 57
[    0.380000] io scheduler noop registered
[    0.390000] io scheduler deadline registered (default)
[    0.400000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.420000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    0.440000] console [ttyS0] enabled, bootconsole disabled
[    0.440000] console [ttyS0] enabled, bootconsole disabled
[    0.470000] m25p80 spi32766.0: found mx25l6405d, expected mx25l3205d
[    0.480000] m25p80 spi32766.0: mx25l6405d (8192 Kbytes)
[    0.490000] 4 ofpart partitions found on MTD device spi32766.0
[    0.500000] Creating 4 MTD partitions on "spi32766.0":
[    0.510000] 0x000000000000-0x000000030000 : "u-boot"
[    0.530000] 0x000000030000-0x000000040000 : "devdata"
[    0.540000] 0x000000040000-0x000000050000 : "devconf"
[    0.560000] 0x000000050000-0x000000800000 : "firmware"
[    0.570000] 0x00000014494c-0x000000800000 : "rootfs"
[    0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.610000] mtd: device 4 (rootfs) set to be root filesystem
[    0.620000] mtd: partition "rootfs_data" created automatically, ofs=0x460000, len=0x3a0000
[    0.640000] 0x000000460000-0x000000800000 : "rootfs_data"
[    0.670000] eth0: done loading
[    0.680000] rt2880_wdt 10000120.watchdog: Initialized
[    0.690000] TCP: cubic registered
[    0.690000] NET: Registered protocol family 17
[    0.700000] 8021q: 802.1Q VLAN Support v1.8
[    0.740000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.760000] Freeing unused kernel memory: 208K (802ac000 - 802e0000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.470000] usbcore: registered new interface driver usbfs
[    9.480000] usbcore: registered new interface driver hub
[    9.490000] usbcore: registered new device driver usb
[    9.530000] SCSI subsystem initialized
[    9.560000] dwc_otg: version 2.72a 24-JUN-2008
[    9.580000] usbcore: registered new interface driver usb-storage
jffs2 is ready
[   11.650000] jffs2: notice: (269) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 0 orphan) found.
switching to jffs2
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[   16.720000] NET: Registered protocol family 10
[   16.750000] Initializing XFRM netlink socket
[   16.760000] NET: Registered protocol family 15
[   16.780000] tun: Universal TUN/TAP device driver, 1.6
[   16.790000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   16.840000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
[   16.870000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   16.920000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[   16.930000] Backport generated by backports.git backports-20140124-0-g1256d3e
[   16.960000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   17.050000] xt_time: kernel timezone is -0000
[   17.120000] cfg80211: Calling CRDA to update world regulatory domain
[   17.190000] cfg80211: World regulatory domain updated:
[   17.200000] cfg80211:  DFS Master region: unset
[   17.200000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   17.220000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   17.240000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   17.250000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   17.270000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[   17.280000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[   17.300000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[   17.350000] PPP generic driver version 2.4.2
[   17.370000] NET: Registered protocol family 24
[   17.470000] rt2800_wmac 10180000.wmac: failed to load eeprom property
[   17.480000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[   17.510000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
[   17.520000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[   30.040000] device eth0.1 entered promiscuous mode
[   30.050000] device eth0 entered promiscuous mode
[   30.080000] br-lan: port 1(eth0.1) entered forwarding state
[   30.090000] br-lan: port 1(eth0.1) entered forwarding state
[   31.020000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   32.090000] br-lan: port 1(eth0.1) entered forwarding state
[   32.980000] cfg80211: Calling CRDA for country: US
[   33.020000] cfg80211: Regulatory domain changed to country: US
[   33.030000] cfg80211:  DFS Master region: FCC
[   33.040000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   33.050000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   33.070000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
[   33.080000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[   33.100000] cfg80211:   (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[   33.120000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
[   33.130000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
[   33.150000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
procd: - init complete -
[   35.700000] rt305x-esw 10110000.esw: link changed 0x00
[   35.740000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   35.750000] device wlan0 entered promiscuous mode
[   35.820000] br-lan: port 2(wlan0) entered forwarding state
[   35.830000] br-lan: port 2(wlan0) entered forwarding state
[   35.840000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   37.370000] rt305x-esw 10110000.esw: link changed 0x02
[   37.830000] br-lan: port 2(wlan0) entered forwarding state
번호 제목 날짜 조회 수
28 ipTIME N702BCM file 2018.04.20 242
27 OpenWRT 빌드환경 구축 (Ubuntu) 2018.04.16 144
26 OpenWRT, DD-WRT 국내 지원 모델 2018.04.13 133
25 Buffalo WHR-G300N V2 2016.04.06 188
24 ipTIME N604M 2016.04.06 253
» SL-R6804 2016.04.06 249
22 TP-LINK TL-WR740N v4.22 2016.04.06 88
21 OpenWRT 이미지 빌드 2014.06.03 85
20 OpenWRT 기본 방화벽 룰셋 2014.06.03 95
19 kernel compile 2014.06.02 20
18 firmware-mod-kit의 펌웨어(bin) 추출과정 설명 2014.05.31 756
17 OpenWRT BuildRoot 중요 디렉토리 및 파일 2014.05.24 120
16 [OpenWRT] gnutls 컴파일 오류 해결방법 2014.05.24 33
15 dts 파일 컴파일 2014.05.23 1302
14 SL-R6804 정보 file 2014.05.23 51
13 MIPS Core군 정리 file 2014.05.19 85
12 OpenWRT 빌드환경 구축 (CentOS 6.5 x86_64) file 2014.05.17 104
11 OpenWRT Boot Sequence 2014.05.17 56
10 OpenWRT BuildRoot 빌드 방법 2014.05.17 198
9 [OpenWRT] OpenVPN Server/Client 설정 2014.05.15 204